2" Plastic Zero Differential Solenoid Valve N/O
Availability: In Stock
Technical Details
SKU
PSL-50K
Position
Normally Open
Port Size
2" Female NPT
Available Voltage
Select Above
Body Material
Engineered Nylon Plastic (PA66)
Components
Stainless Steel
Seal Material
EPDM Diaphragm
Orifice Size
50 mm
Temp Range
15 to 175° F | -10 to 80°C
Pressure Range
0 - 60 PSI (No Minimum)
Flow Rate
Cv 48 (Appx 345 GPM @ 60 PSI)
Power
AC: 35 VA (220V), 36 VA (110V), 30 VA (24V) | DC: 38 W (24V), 36 W (12V)
Coil Connection
DIN 43650A
Coil Class
Class H (356°F)
Protection Class
IP65
Response Time
Fast Acting (Less than one second)
Duty Cycle
100% Duty at Rated Ambient Temperature
Suitable Media
Water – Air - Gas
Weight
2 lb 14 oz
Height
7.68"
Length
6.26" port to port
Width
7.95"
Product Overview
The PSL-50K is our 2”, two-way, zero-differential normally open valve. This valve is considered a semi-direct acting or assisted-lift solenoid valve. These are extremely versatile in that they can work from zero bar while still boasting a high flow rate. This valve has a 50mm internal orifice and a flow rate of 48 Cv. At the maximum pressure, 60 PSI, this equates to a flow of 345 gallons per minute! The large internal orifice and zero-differential pressure requirement make this valve excellent for gravity feed applications as well.
This is a 2-way valve, meaning it has two ports: an inlet port and an outlet port. These ports are threaded with Female National Pipe Thread, making installation easy and tool-free. Normally Open refers to the position the valve is in without power; this valve will be open without power and close when energized.
Molded from PA66 Nylon Plastic, our 2” Normally Open Valve is not only large but built solid. This is a good substitute for stainless steel valves, as it is completely lead-free and offers great chemical resistance. When designing this valve, we opted for EPDM diaphragms for this line-up. We found this seal offers better resistance to higher temperatures than NBR or Viton seals. Similar to the PA66 body, this diaphragm has great chemical resistance.
The PSL-50K comes with our tough and reliable 210 Series coil. For easy installation, this coil comes standard with a 43650A DIN connector. This allows installers to run wires directly from the power supply into the screw-down terminals inside the connector. This valve can be configured in any of the five most common coil voltage configurations: 12VDC, 24VDC, 24VAC, 110VAC, and 220VAC. Our 210 coils require 38 Watts for the DC voltages and 36VA for the AC voltages. Similar to most solenoid valves, this is a constant power draw when energized; it is encouraged to reserve additional power than required to account for variances in the outputs of different power sources.
Common Applications
- This valve is extremely popular with potable water applications and home uses.
- This valve can be used with air, gas, fuel, diluted acids, ketones, alkalis, and food-grade applications.
- These coils have an IP65 waterproof level, making them great for indoor or outdoor use and short-term protection against splashing and low-pressure water jets at all angles.
Installation
- The valve must operate in the direction noted by the arrow molded into the body.
- A pre-filter is recommended to keep the diaphragm free from debris and the valve functioning properly.
*Consult a chemical compatibility expert for correct seal and valve body material choice.
Wiring Instructions
- Loosen and remove the Phillips-head screw securing the DIN connector to the coil.
- Detach the DIN connector from the coil.
- Open the DIN connector housing by prying at the small slot located in the bottom corner next to the Earth terminal.
- Inside the housing, locate the screw terminals:
- Terminal 1: Connect the hot or positive wire.
- Terminal 2: Connect the neutral or negative wire.
- Earth Terminal (for AC voltages only): Connect the ground or Earth wire.
- Ensure all screw terminals are securely tightened for a reliable connection.
- Reassemble the DIN connector by reversing the steps above.
